Thursday, November 10, 2016

Classic Tubes: Reynolds 753

Any fan of vintage racing and touring bikes is more than familiar with the famous green, black and gold decal signifying Reynolds 531 tubing. Regardless of whether someone preferred Campagnolo, Simplex, Huret, Zeus, or whatever components for their bike, up until the 1980s Reynolds 531 was probably one of the most common elements of any high-quality lightweight bicycle. But in the 1970s, in a quest to reduce weight amid early experiments with titanium and carbon fiber bicycles, the Reynolds company introduced a new tubing that they hoped would give them the competitive edge and become the ultimate steel tubeset: 753.

Reynolds 753 was essentially a heat-treated version of the company's familiar 531 manganese alloy steel. The heat treating boosted the tensile strength of the steel by about 50% and made it possible to draw the tubing much thinner than regular 531. Some versions of the tubing were drawn down as thin as 0.3mm in the center sections of butted tubes! It was claimed that the result could drop more than a pound from the weight of a bicycle frame without sacrificing strength.

Originally developed and tested in secret in the early '70s, Reynolds 753 was introduced to the public at the Paris Cycle Show in the Fall of 1975, but the company could already boast of a world championship (in the 5000m pursuit) and a new world record (50 mile time trial) with the tubing. The Raleigh racing team had raced in 1974 on 753 frames that were labeled as 531.

Reynolds introduced both 753 and their 531SL
to the public at the same trade shows in '75.
Note that this early ad already proclaims a
World Championship won with 753, before it
was released to the public. (image from Velo Pages)
Although it was no longer a secret by 1976, it would take a couple of years before the general public would be able to get their hands on bikes built with the hot new tubing. Not surprisingly, the first company to offer it was Raleigh, which was at that time a wholly-owned subsidiary of TI Reynolds. But also, the tubing was not available or intended for mass production. Because of the need to preserve the strength gained in heat treating, low-temperature silver brazing was the only acceptable way to join 753 tubing, and this required very close tolerances for mitering and lug fit when building. Also, the tubing could not be cold set after brazing, so alignment had to be spot-on from the beginning. Because of the special care needed to ensure a proper build, any framebuilder who wanted to use it had to be certified by Reynolds. The certification process involved getting a sample tubeset, then brazing a frame which had to be sent to Reynolds for destructive testing. The inspectors would look for close mitering tolerances, good brazing penetration, and any signs of overheating in the joint and tubing. Only when certified could a builder be supplied with 753 tubing.

According to The Custom Bicycle by Kolin and de la Rosa (1979), by 1978 the only 753-certified builders in the U.K. were Raleigh, Bob Jackson, and Harry Quinn. Although not listed as such in the Kolin book, I know for a fact that Mercian was certified by '79. Jim Merz of Oregon and Proteus Design in Maryland were among the first certified builders in the USA, though many others would follow suit. In the US, I've heard that many builders took it as proof of their accomplishment and skill to be 753-certified, even if they never built more than a handful of frames with the material.
Mercian was offering the 753 Special starting in
1979. This is from the catalog that was released
around '79 - '80. I recently acquired one of these,
so expect more info about it in the not-too-distant
future.

One interesting thing about 753 was that when it was first introduced, it was only available in metric dimension tubing. Metric dimensions were primarily used on French bikes at the time, while British, Italian, and most American custom-built bikes followed Imperial or fractional inch dimensions. For example, Imperial tubing dimensions were as follows: top tube, 1-in. (25.4mm); down-tube and seat-tube, 1 1/8-in. (28.6mm). French dimensions were: top tube, 26mm; down-tube and seat-tube, 28mm. I have not been able to find any explanation as to why the metric dimensions were used originally for 753. As I understand it, later versions of the tubing were made to Imperial dimensions, and would have been labeled 753R.

Not all 753 was drawn to ultra-thin walled gauges. Even from the beginning there were a couple of different gauges available. The thinnest was more common in smaller frames, while larger frames would normally have slightly thicker gauge tubes. The "cutoff" was likely somewhere around 58 or 59cm frame size - though that is not necessarily a universal fact. I've read arguments that individual builds might have taken the rider into account, so there could be exceptions where a larger frame might still have the thinner tubeset, or the other way around. If someone has an earlier-model 753 frame, one way to figure out which gauge tubing was used is to look at the seatpost size. A high-quality lightweight bike frame built with 531, or even Columbus SL tubing would normally take a 27.2mm seatpost, and in many cases (but not all), a smaller seatpost would indicate thicker-walled and heavier tubing. But most frames built with the metric-dimensioned 753 would require a 27mm seatpost. Larger frames would likely take a 26.8mm post.

So, how did they come up with the name for the new tubing? It's fairly well known that Reynolds 531 was named for the makeup of the alloy -- 5 parts manganese, 3 parts carbon, and 1 part molybdenum. It also had a tensile strength right around 53 tons/in². According to Tony Hadland's book Raleigh: Past and Presence of an Iconic Bicycle Brand, Reynolds 753 had a tensile strength of about 75 tons/in² and was drawn to .3mm in the center section of the tubes. Also, it was introduced in 1975, and the tubing was the result of their 3rd material tested.

Over the years, there would be variations on 753 released. In addition to the standard road set (later designated as 753R) there was a track tubeset which used the thinnest possible gauges (753T), a heavier-duty version for mountain and touring use (753ATB), and later still a slightly oversized diameter version (753OS).

Through the 1980s, bikes with 753 were something of a holy grail to some, and could be seen on some of the best professional racers' bikes. Bernard Hinault rode 753-tubed bikes for many of his professional wins, as did Greg LeMond as a member of the La Vie Claire team. Laurent Fignon's bikes in the '89 tour used it, too. Lots of pro teams did. But among the mere mortals, it always remained fairly uncommon. Price was always a concern. The fact that it could be pretty finicky to work with, and the certification process also kept it more exclusive. Still, there were a number of custom builders here in the U.S. who used it, and even some larger operations like Trek and Waterford built quite a few 753 frames. Even Rivendell, when it first was getting started in the 1990s, had their early bikes built by Waterford out of 753 (though I'm pretty sure it wasn't the super thin-walled versions).

Then, in 1995, twenty years after the introduction of 753, Reynolds introduced 853 -- an air-hardening alloy that had even more strength than 753 but did not require special handling or certification. More importantly, 853 could be welded, which by the '90s had become a much more common way to build bicycles. Two years later, the company introduced 725 heat-treated chrome-moly, which had a lot of the same physical properties of 753, but likewise required no certification and could be welded. Though I've read that a builder can still purchase 753, I doubt many bother since there are alternatives that are easier to work with. No, 753 was probably the top frame tubing a person could buy for its time, but that time is past. Still, for a classic bicycle fan, finding a vintage example is kind of a thrill. I'll come back to that again in future posts.

15 comments:

  1. Thank you for another excellent post about a great classic bike component.

    I can think of one possible reason why 753 was originally offered only in metric dimensions: Britain had adopted the metric system a couple of years earlier. So, at the time, it seemed as if its bicycle industry--and the US--would follow suit. Funny that we now have a mishmash of metric and imperial dimensions in the bike world: Road frames are usually measured in centimeters, but mountain bikes in inches. Also, we use one-inch headsets and 9/16 pedal threads but measure crank arm lengths and seat post diameters in millimeters.

    Also, I think that after the British, the French were seen as the most likely to use an ultra-light tubing like 753.

    ReplyDelete
  2. I believe Holdsworth (UK's Planet-X) is offering frames in 753 now?

    http://www.planetx.co.uk/news/products/q/date/2016/04/05/handbuilt-holdsworth-753-will-be-launched-at-bespoked

    I built a frame (in a week on a 1-1 framebuilding course) from 853 a few years ago. Lovely stuff and not hard to work with at all

    ReplyDelete
  3. I have a 753 frame custom built by legendary NZ frame builder Eddie Bosomworth. I commissioned it in 1986 and it sports braze-on shift lever bosses, front derailleur mount, two sets of water bottle mounts and internal top tube cable routing. Several of these features were rare in 753 as builders were reluctant to apply heat to those thin central parts of the tube. My bike is 60cm and takes a 27.2 seat post, and again that was unusual for a large frame. In those days I was very light (65kg and 183cm) and Eddie believed the 0.3mm wall thickness would not be a problem. He has proven to be correct - the frame is now 30 years old and in perfect condition. Frame and fork weigh in at 1896g, which is not bad for a 60cm frame.

    One of the problems you don't mention is that the thin walls made the tubing susceptible to denting. I raced and was a bike mechanic for a number of years and I saw more than one 753 frame with a dented top tube where the distraught owner had rested his saddle against a post to have the bike roll forward and clunk the top tube.

    ReplyDelete
    Replies
    1. You're right about the susceptibility to denting -- it is a little easier with such thin-walled tubes. Got to be careful with it.

      Delete
    2. This comment has been removed by the author.

      Delete
    3. 1896 grams would be frame without forks.

      Delete
  4. I have a '97 Jackson Arrowhead 753. Still my favorite bike ever although it has taken a back seat lately to my HD Sportster. But that will changed as soon as I get my Jackson back from the LBS! The only problem I have now is that it is becoming difficult to find Campy parts. Unless I want to put on the ugly ones. Especially these new four-arm cranks. If I wanted Shimano I would buy Shimano! Are you listening Campy?

    ReplyDelete
    Replies
    1. LOL, the Sportster was totaled! My Jackson is back to the top of the list!

      Delete
  5. Dear RG. I thought you mike like a 753 Master Framebuilder certificate to go with the article: http://preview.tinyurl.com/grhakzb

    I did my test about 20 years ago, not too difficult, just a BB shell DT/ST and CS stubs: http://preview.tinyurl.com/juu8xbl

    You're right...I only built 2 frames from the stuff (much preferred Columbus), but that was the only sort of certification around, so it gave the customers a degree of confidence.

    All the best, Dan Chambers

    ReplyDelete
  6. Love your site Retrogrouch ....and yes Old is Good! I can relate to your views on bikes, I too am very opinionated about all things bikes. Your correct simple beautiful bikes are the way to go. Most folks see me riding one of my old Motobecanes and say what a beautiful bike but how can you ride such a old thing? All I say you haven't rode anything until you experience the "Magic Carpet Ride"of Reynolds 531....IMO the most perfect bike frame material ever made. I tell them when their bike made of plastic is in a landfill somewhere my heirs will still be riding one of these!!!!!

    ReplyDelete
  7. RG, Out of curiosity, Is there a published number of the 753 certifications granted?

    ReplyDelete
    Replies
    1. There may well be, but I'm not sure where one would find them.

      Delete
  8. Excellent write up. I had to come back for a second read today just to make myself more sick about a missed opportunity. I online bike shop every day. I see screamin deals every single day. Just got a NOS Trek 1000 SL frameset for a cordless screwdriver day before yesterday. But that has nothing to do with what brought me here. Today on offerup there was a Bob Jackson model 753 (made from 753 of course) in beautiful condition. The woman was asking $150! It was 50 miles from me and I don't drive at the moment but i damn near hopped on my new Trek and brought it home strapped to my hiking pack... but someone with a good eye got it within minutes of me seeing it. I just hope they treat it right. Anyway, today's bikes should be getting listed soon. Hopefully I find something rad.

    ReplyDelete
  9. Brooks, great article, thank you, appreciate it very much.

    ReplyDelete
  10. Ah, my 753 Dave Moulton Fuso...what a bike. I gave myself a present after losing a fair amount of weight back in 1989 or so. I unloaded my Davidson with full Record for the 753 Fuso. Blue/Black, full Mavic equipe' GL330 rims shod with 15/16/15 Wheelsmith Aero spokes, silk sewups only...white seat, cable housings and bar tape...what a bitchen' ride. Pre index shifting, Look titanium pedals, Modolo stem/bars...a retrogrouch bike in an era of rapidly advancing modernism. I rode my Gios Torino or Fuso Fr1 on ordinary club rides, but when it came to a particularly hairy or long ride, I pulled out the 753 Fuso. It never let me down. Folks scoffed at the subtle differences their Columbus tubes and 753, but I could tell between the two in my backside and hands. The people that knew understood that this machine had breeding, or as Ettore Bugatti called it,
    "Pur Sang".

    ReplyDelete